Owner guide · Elgin CDJR · Streamwood, IL
Jeep Grand Cherokee Jack Points and Jack Location
Changing a flat on a Grand Cherokee starts with knowing where the jack is and exactly where it goes under the vehicle. The 2026 Jeep Grand Cherokee owner's manual covers jacking and wheel changing as an If Equipped item. Here is where the jack and spare are stored, the front and rear jacking points, and the steps the manual gives.
Under the load floorwhere the jack and tools are stored
Triangle symbolmarks the lift points on the sill molding
130 ft-lblug nut torque
After 25 milescheck the lug nut torque again
The short answer
Per the 2026 Grand Cherokee owner's manual, for the front axle place the jack on the body flange just behind the front tire, and for a rear tire place it in the slot on the rear tie-down bracket, just forward of the rear tire. Both spots are indicated by the triangular lift point symbol on the sill molding. Do not raise the vehicle by the body side sill molding. The scissor-type jack and tire changing tools are in the rear cargo area, under the load floor.
Before you jack up a Grand Cherokee
The manual lists these preparations for jacking:
- Park on a firm, level surface as far from the edge of the roadway as possible. Avoid icy or slippery areas.
- Turn on the Hazard Warning Flashers.
- Apply the parking brake.
- Place the gear selector into PARK (P).
- Turn OFF the ignition.
- Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if changing the left front wheel, block the right rear wheel.
If your vehicle has air suspension, the manual notes a feature that allows the automatic leveling to be disabled before changing a tire, through the Uconnect system. It also says to disable the hands free liftgate before changing a tire or using the jack. Passengers should not remain in the vehicle when it is being raised. More on air suspension in our Grand Cherokee air suspension guide.
From the 2026 Jeep Grand Cherokee Owner's Manual (Jacking The Vehicle And Wheel Changing and Preparations For Jacking, page 275), read November 4, 2026.
Where the jack is on a Grand Cherokee
The scissor-type jack and tire changing tools are located in the rear cargo area, under the load floor. The manual notes that, depending on the trim level, the jacking tool locations vary between second and third row seating models.
To get to them, lift up on the load floor handle, then remove the jack storage cover by firmly pressing the two side tabs inward while lifting up or out. Release the Velcro straps and pull outward or up on the jack and tools to remove them.
- Jack tool bag
- Lug nut wrench
- Tow hook (If Equipped)
- Jack handle extension (If Equipped)
- Fuel funnel
- Scissor jack
From the 2026 Jeep Grand Cherokee Owner's Manual (Jack Location and Jack And Tools Description, pages 275 to 277), read November 4, 2026.
Where the spare tire is
The manual says spare tire locations vary between second and third row seating, depending on trim level. Remove the spare before attempting to jack up the vehicle.
Second row seating
The spare tire is located in the rear cargo area under the load floor. Lift up on the rear load floor, remove the fastener securing the spare by rotating it counterclockwise, and lift the spare out.
Third row seating
The spare is stowed under the rear of the vehicle by a cable winch. Lift up on the rear load floor and remove the winch plug to expose the winch access hole, just inside the liftgate opening, fit the jack handle extension over the winch drive nut and turn counterclockwise with the lug wrench until the spare is fully lowered and the winch stops.
Winch caution
The winch mechanism is designed for use with the jack wrench extension tool only. Use of an air wrench or power tool may damage the winch.
From the 2026 Jeep Grand Cherokee Owner's Manual (Spare Tire Stowage and Spare Tire Removal, pages 277 to 279), read November 4, 2026.
Grand Cherokee front and rear jacking points
Front jacking point
For the front axle, place the jack on the body flange just behind the front tire, as indicated by the triangular lift point symbol on the sill molding. The jack must be placed straight on with the handle facing outwards.
Rear jacking point
For a rear tire, place the jack in the slot on the rear tie-down bracket, just forward of the rear tire, as indicated by the triangular lift point symbol on the sill molding.
Not the sill molding
Do NOT raise the vehicle by the body side sill molding. Be sure the jack is placed in the proper engagement location on the inside of the panel; damage may occur if the procedure is not followed.
Fully engaged first
Do not raise the vehicle until you are sure the jack is fully engaged. Do not attempt to raise the vehicle by jacking on locations other than those in the jacking instructions.
From the 2026 Jeep Grand Cherokee Owner's Manual (Jacking Instructions, pages 280 and 281), read November 4, 2026.
Changing the tire, step by step
With the spare removed and the jack and tools assembled, the manual gives these steps:
- Loosen (but do not remove) the wheel lug nuts one turn counterclockwise while the wheel is still on the ground.
- Place the jack at the front or rear jacking point for the wheel you are changing.
- Raise the vehicle by turning the jack screw clockwise, only until the tire just clears the surface and there is enough clearance to install the spare.
- Remove the lug nuts and wheel.
- Position the spare on the vehicle and install the lug nuts with the cone-shaped end toward the wheel. Lightly tighten the nuts.
- Lower the vehicle by turning the jack screw counterclockwise, and remove the jack and wheel blocks.
- Finish tightening the lug nuts in a star pattern until each nut has been tightened twice.
The manual warns never to start or run the engine while the vehicle is on a jack, never to put any part of your body under a vehicle on a jack, and not to tighten the wheel nuts fully until the vehicle has been lowered. The jack is designed as a tool for changing tires only, not for lifting the vehicle for service.
From the 2026 Jeep Grand Cherokee Owner's Manual (Preparations For Jacking warnings, page 275; Jacking Instructions, pages 279 to 281), read November 4, 2026.
Lug nut torque and after the change
The manual's wheel and tire torque specifications:
| Item | Specification |
|---|---|
| Lug nut/bolt torque | 130 ft-lb (176 N·m) |
| Lug nut/bolt size | M14 x 1.50 |
| Lug nut/bolt socket size | 22 mm |
From the 2026 Jeep Grand Cherokee Owner's Manual (Wheel And Tire Torque Specifications, page 392; Jacking Instructions, page 282), read November 4, 2026.
After 25 miles (40 km), check the lug nut torque with a torque wrench to ensure that all lug nuts are properly seated against the wheel. Do not drive with the spare tire installed for more than 50 miles (80 km) at a max speed of 50 mph (80 km/h), and have the road wheel and tire repaired as soon as possible. Always stow the jack parts and the spare tire in the places provided.
Jeep tire service at Elgin CDJR
Our service department is open Monday to Friday 7 a.m. to 7 p.m. and Saturday 7:30 a.m. to 4 p.m., and is closed Sunday. Elgin CDJR is at 1500 W. Lake St. in Streamwood. Get directions.
Need the flat repaired or replaced, or the lug nuts checked? Schedule service online, or see our Jeep service center.
Jeep Grand Cherokee jack points FAQ
Where are the jack points on a Jeep Grand Cherokee?
Per the 2026 owner's manual, the front point is the body flange just behind the front tire, and the rear point is the slot on the rear tie-down bracket just forward of the rear tire. Both are indicated by the triangular lift point symbol on the sill molding.
Where is the jack in a Jeep Grand Cherokee?
The scissor-type jack and tire changing tools are in the rear cargo area, under the load floor, behind a jack storage cover.
Where is the spare tire on a Grand Cherokee?
On second row seating models it is under the rear cargo load floor. On third row seating models it is stowed under the rear of the vehicle on a cable winch.
Can I jack a Grand Cherokee by the side sill?
No. The manual says do NOT raise the vehicle by the body side sill molding; use only the jacking locations shown in the jacking instructions.
What is the lug nut torque on a Jeep Grand Cherokee?
The 2026 owner's manual lists 130 ft-lb (176 N·m), with M14 x 1.50 lug nuts and a 22 mm socket. Check the torque again after 25 miles (40 km).
How far can I drive on the Grand Cherokee spare?
The manual says not to drive with the spare tire installed for more than 50 miles (80 km) at a max speed of 50 mph (80 km/h).
What are the service department hours?
Monday to Friday 7 a.m. to 7 p.m. and Saturday 7:30 a.m. to 4 p.m. We are closed Sunday.
Got a flat on your Grand Cherokee?
Schedule a visit at Elgin CDJR in Streamwood and we will take care of the tire and check the lug nuts.
Sources
Jack and spare locations, jacking points and steps are from the 2026 Jeep Grand Cherokee Owner's Manual (publication 102427_26_WL, edition E1) on Mopar's owner information site, read on November 4, 2026. Jacking equipment is an If Equipped item and other model years and models describe it in their own manuals, so check yours. Our address and service hours are from our own website, checked the same day.
- 2026 Jeep Grand Cherokee Owner's Manual (Jacking The Vehicle And Wheel Changing; Wheel And Tire Torque Specifications), Jeep / Mopar, read November 4, 2026
- Jeep Service Center in Streamwood: services and service hours, Elgin CDJR
- Home page: service department address and hours, Elgin CDJR