Jeep Cherokee · Elgin CDJR · Streamwood, IL

Jeep Cherokee Jack Points

Where the jack goes on the new Jeep Cherokee, the lift point covers you remove first, where the jack and spare are stowed, and how to raise the vehicle to change a tire, from the 2026 Jeep Cherokee owner's manual.

Red 2026 Jeep Cherokee, front three-quarter view
2026 Jeep Cherokee. Illustrative photo.
Front + rearJacking locations shown in the manual
CoversRemove the lift point covers before jacking
LiftgateJack and tools (if equipped) in the rear storage compartment
130 ft-lbWheel bolt torque (176 N·m)

The short answer

The 2026 Jeep Cherokee owner's manual shows a front and a rear jacking location. Its Jacking Locations image marks them on the underside of the body side, just behind the front wheel and just ahead of the rear wheel. Before placing the jack, you remove the lift point covers, then put the jack under the lift point closest to the flat tire and turn the jack screw clockwise until the jack saddle firmly engages the lift point. The jack and tools, if equipped, are stowed in the rear storage compartment, under the access cover you lift with the load floor handle.

Where to put the jack on a Jeep Cherokee

The manual says placement for the front and rear jack locations is critical, and shows them in a Jacking Locations image:

LocationWhat the manual's image shows
Front lift pointUnderside of the body side, just behind the front wheel
Rear lift pointUnderside of the body side, just ahead of the rear wheel

The manual shows lift point covers that you remove first. Its steps say to remove the lift point covers, then place the jack underneath the lift point that is closest to the flat tire and turn the jack screw clockwise to firmly engage the jack saddle with the lift point.

The manual cautions: do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle.

From the 2026 Jeep Cherokee Owner's Manual, Jacking Instructions; Lift Point Cover and Jacking Locations images (pp. 181-182), read November 17, 2026.

Where the jack and spare are stowed

The manual's section is titled "Jacking The Vehicle And Wheel Changing — If Equipped," so a jack and spare may not be fitted to every Cherokee. On vehicles that have them, the jack and tools are in the rear storage compartment:

  1. Open the liftgate.
  2. Lift the access cover using the load floor handle.
  3. Remove the fastener securing the spare tire, jack and wrench, and remove the spare wheel and tools from the vehicle.

Spares, flat or inflated, must be stowed with the valve stem facing the ground. The manual also describes a Tire Service Kit, if equipped, stowed under the load floor in the frunk; it can seal small punctures up to 1/4 inch (6 mm) in the tread.

From the 2026 Jeep Cherokee Owner's Manual, Jack Location/Spare Tire Stowage, Jacking Instructions and Tire Service Kit (pp. 180-182), read November 17, 2026.

How to jack up a Jeep Cherokee to change a tire

Before you raise the vehicle, the manual lists these preparations:

  1. Park on a firm level surface as far from the edge of the roadway as possible. Avoid icy or slippery areas.
  2. Turn on the Hazard Warning Flashers.
  3. Apply the parking brake.
  4. Place the gear selector into PARK (P).
  5. Place the ignition in the OFF position.
  6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the driver's front wheel is being changed, block the passenger's rear wheel.

Passengers should not remain in the vehicle while it is being lifted or raised.

Raising the vehicle and changing the wheel:

  1. Remove the spare tire, jack and tools from the stored location.
  2. Before raising the vehicle, use the wheel bolt wrench to loosen, but not remove, the wheel bolts on the wheel with the flat tire. Turn them counterclockwise one turn while the wheel is still on the ground.
  3. Remove the lift point covers.
  4. Place the jack underneath the lift point closest to the flat tire and turn the jack screw clockwise to firmly engage the jack saddle with the lift point.
  5. Raise the vehicle just enough to remove the flat tire.
  6. Remove the wheel bolts and tire, mount the spare tire with the valve stem facing outward, and install and lightly tighten the wheel bolts.
  7. Lower the vehicle to the ground by turning the jack handle counterclockwise. Do not tighten the wheel bolts fully until the vehicle has been lowered.
  8. Finish tightening the wheel bolts in a star pattern until each one has been tightened twice, pushing down on the end of the wrench handle for leverage.
  9. Lower the jack until it is free, reassemble the lug wrench to the jack assembly, stow it in the spare tire area and secure it. Release the parking brake before driving.
  10. After 25 miles (40 km), check the wheel bolt torque with a torque wrench to make sure all the wheel bolts are properly seated against the wheel.

From the 2026 Jeep Cherokee Owner's Manual, Preparations For Jacking and Jacking Instructions (pp. 179-182), read November 17, 2026.

Wheel bolt torque

Lug nut/bolt torqueLug nut/bolt sizeSocket size
130 ft-lb (176 N·m)M14 x 1.5022 mm

The manual says to use only authorized dealer recommended lug nuts/bolts, clean off any dirt or oil before tightening, and inspect the wheel mounting surface and remove any corrosion or loose particles before mounting the tire. If in doubt about the correct tightness, have them checked with a torque wrench by an authorized dealer or service station. For more detail, see our Jeep Cherokee lug nut torque guide.

From the 2026 Jeep Cherokee Owner's Manual, Torque Specifications (p. 247), read November 17, 2026.

Safety rules from the manual

  • The jack is designed to be used as a tool for changing tires only. It should not be used to lift the vehicle for service purposes; if you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.
  • Never put any part of your body under a vehicle that is on a jack, never start or run the engine while the vehicle is on a jack, and do not let anyone sit in the vehicle when it is on a jack.
  • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. Do not attempt to raise the vehicle at any other location.
  • Raising the vehicle higher than necessary can make it less stable. Raise it only enough to remove the tire.
  • Do not change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid being hit.
  • A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants. Always stow the jack parts and the spare tire in the places provided, and have the flat tire repaired or replaced immediately.

From the 2026 Jeep Cherokee Owner's Manual, Preparations For Jacking and Jacking Instructions (pp. 179-182), read November 17, 2026.

Cherokee tire and wheel service at Elgin CDJR

Our service department works on the Jeep Cherokee, wherever it was bought, including tire service and tire rotations. Visit our Jeep service center or parts center, schedule service or see our service specials.

Our service department is open Monday to Friday 7 a.m. to 7 p.m. and Saturday 7:30 a.m. to 4 p.m., and is closed Sunday. Elgin CDJR is at 1500 W. Lake St. in Streamwood. Get directions.

Jeep Cherokee jack points FAQ

Where are the jack points on a Jeep Cherokee?

In its Jacking Locations image, the 2026 owner's manual shows a front and a rear lift point, on the underside of the body side just behind the front wheel and just ahead of the rear wheel. Remove the lift point covers before placing the jack.

Where is the jack in a Jeep Cherokee?

On vehicles equipped with a jack and spare, they are in the rear storage compartment. Open the liftgate, lift the access cover with the load floor handle, and remove the fastener securing the spare tire, jack and wrench.

How high should I raise the Cherokee?

Only enough to remove the flat tire. The manual warns that raising the vehicle higher than necessary can make it less stable.

Can I use the jack to work under my Cherokee?

No. The manual says the jack is designed for changing tires only and should not be used to lift the vehicle for service. Take it to a service center where it can be raised on a lift.

What is the wheel bolt torque on a Jeep Cherokee?

130 ft-lb (176 newton meters), with M14 x 1.50 lug nuts/bolts and a 22 mm socket, according to the 2026 owner's manual.

What are your service hours?

Monday to Friday 7 a.m. to 7 p.m. and Saturday 7:30 a.m. to 4 p.m. We are closed Sunday.

Sources

Jacking, stowage and torque information is from the 2026 Jeep Cherokee owner's manual (FCA US LLC), read November 17, 2026. Equipment varies by vehicle and model year; follow your own owner's manual. Our address, service hours and the models we service are from our own website, checked the same day.

  1. 2026 Jeep Cherokee Owner's Manual: Preparations For Jacking, Jack Location/Spare Tire Stowage, Jacking Instructions, Tire Service Kit (pp. 179-182), Torque Specifications (p. 247), FCA US LLC via vehicleinfo.mopar.com, read November 17, 2026
  2. Jeep service center page: Jeep models serviced, service hours, address, Elgin CDJR, read November 17, 2026