Jeep Gladiator · Elgin CDJR · Streamwood, IL
Jeep Gladiator Hard Top Removal Guide
How to take out your Gladiator's Freedom Panels, store them in the panel bag, remove and reinstall the whole hard top, and fit the optional Sunrider for Hard Top, following the 2026 Jeep Gladiator owner's manual.

The short answer
The 2026 Jeep Gladiator owner's manual says to remove the left Freedom Panel before the right: fold down the sun visor, turn the three L-shaped locks, unlatch the header panel latch and lift the panel out. To remove the whole hard top, open both front doors, remove the two Torx screws at the B-pillars, the two along the interior body side and the four along the back of the cab with the #T50 Torx driver, disconnect the wire harness at the left rear corner, and lift the top off with four adults, one at each corner.
Removing and installing the Freedom Panels
The hard top has a left side panel, a right side panel and the hard top itself. The manual says the left side panel must be removed before the right side panel.
- Fold down the sun visor against the windshield.
- Turn the three L-shaped locks on the left side panel (front, rear and outside) to unlock them from the roof.
- Unlatch the left side header panel latch at the top of the windshield.
- Remove the left side panel.
- Repeat these steps to remove the right side panel.
To install the panels, set the right side panel on the windshield frame with the locating pin in the front receiver mounting hole, then the left side panel, making sure there is no overhang and the panels sit flush with the body. Secure them by doing the removal steps in reverse order. To prevent water leaks, clear the seals and panels of dust and debris first.
From the 2026 Jeep Gladiator Owner's Manual, Hard Top Front Panel(s) Removal; Hard Top Front Panel(s) Installation (pp. 82-84), read November 17, 2026.
Using the panel storage bag (if equipped)
The storage bag has two compartments. Lay it down with the loops and hooks facing up, unzip it and fold back the outer flap. Make sure each panel's front latch is closed before you put it in the bag.
- Insert the left side panel with the latches facing up.
- Unfold the black panel divider so it lies flat.
- Insert the right side panel with the latches facing down.
- Unfold the outer flap and zip the bag closed.
- Store the bag in a safe location.
From the 2026 Jeep Gladiator Owner's Manual, Hard Top Panel(s) Storage Bag (p. 84), read November 17, 2026.
Removing the whole hard top
- Open both front doors.
- With the provided #50 Torx head driver and ratchet, remove the two Torx screws that secure the hard top at the B-pillars, near the top of the front doors.
- If equipped, remove the lower interior soft trim panel by pulling it away from the trim (it is held by hook-and-loop fasteners).
- With the #T50 Torx driver, remove the fasteners that secure the hard top: two along the interior body side, rearward of the back doors, then four along the back of the cab.
- Find the wire harness at the left rear inside corner. Push the plastic cover to the side and slide it off. Do not force it, or it will break.
- Release the harness by pulling back the red latch, then pushing down the black button while pulling the harness out.
- Remove the hard top with four adults, one at each corner. Install the provided edge protectors along its bottom edges and set it on a soft surface.
- Remove the storage cover on the quarter trim, using the mechanical key blade to pry it open.
- Tuck the wire harness into the storage compartment and replace the cover.
From the 2026 Jeep Gladiator Owner's Manual, Removing The Hard Top (pp. 84-86), read November 17, 2026.
Installing the hard top
If the door frames are installed from soft top use, remove them before installing the hard top. Place the top on the truck so it sits flush with the body at the sides and across the back, then follow the removal steps in reverse order. Inspect the seals and replace them if damaged. When reinstalling the soft trim panel, center it so there is an even gap on both sides and press over the hook-and-loop fasteners.
| Fastener | Torque from the manual |
|---|---|
| Hard top to body Torx fasteners (#T50) | 155 in-lb +/- 22 in-lb (17.5 N·m +/- 2.5 N·m) |
| Sunrider front and rear door rail bolts | 8.8 ft-lb (12 N·m) |
| Sunrider rear clamp bolts | 3.7 ft-lb (5 N·m) |
Do not overtighten the Torx fasteners, or the retainers will be damaged.
From the 2026 Jeep Gladiator Owner's Manual, Installing The Hard Top; Sunrider For Hard Top (pp. 86-87), read November 17, 2026.
Sunrider for Hard Top (if equipped)
The Sunrider soft top can be used in place of the Freedom Panels to open the area above the front seats. Do not open or close it while driving.
- Remove both front Freedom Panels.
- With a second person, set the Sunrider top on the vehicle, lining up the holes at the front and rear of the side rails.
- Swing the front frame bracket around the side of the rail and insert the front door rail bolt (the one without a spacer) from underneath. Tighten with a #40 Torx driver until snug.
- Insert the rear door rail bolt (the one with a spacer) from underneath and tighten until snug.
- Repeat on the other side.
- Attach the rear clamp at the rear center of the top with the two provided bolts and tighten until snug.
- From inside, use the handle on the front header to pull the top forward into the closed position.
- Pull each header latch handle down to engage the hook, then pull it back up while squeezing the hook to lock it.
To open it, fold both sun visors forward, release both header latches, then lift and push the top rearward to the Sunrider position and secure it with the two hook-and-loop fasteners from the kit.
From the 2026 Jeep Gladiator Owner's Manual, Sunrider For Hard Top (pp. 86-88), read November 17, 2026.
Cautions and roof loads
| Topic | What the manual says |
|---|---|
| Moving the truck | Do not move the vehicle until the top is either fully attached to the windshield frame and body, or fully removed. |
| Water | The manual recommends the top be free of water before you remove the panels; removing the top, opening a door or lowering a window while it is wet can let water drip inside. Position the top and panels properly to seal, and handle and store them carefully to protect the seals. |
| Loads on the top | The hard top is not designed to carry additional loads such as aftermarket roof racks, spare tires, building materials, or hunting or camping supplies. |
| Roof Luggage Rack (if equipped) | For Hard Top models only. The roof load must not exceed 100 lb (45 kg), including the crossbars, and should be spread evenly. Use the crossbars whenever cargo is on the rack. |
Have a Wrangler instead? See our Wrangler hard top removal guide and 2026 Wrangler roof options guide.
From the 2026 Jeep Gladiator Owner's Manual, Hard top cautions; Roof Luggage Rack (pp. 82, 86, 88), read November 17, 2026.
Jeep Gladiator service and parts at Elgin CDJR
Our Mopar service department works on the Jeep Gladiator, wherever it was bought. Visit our Jeep service center or parts center, schedule service or see our service specials.
Our service department is open Monday to Friday 7 a.m. to 7 p.m. and Saturday 7:30 a.m. to 4 p.m., and is closed Sunday. Elgin CDJR is at 1500 W. Lake St. in Streamwood. Get directions.
Jeep Gladiator hard top FAQ
Which Gladiator Freedom Panel comes off first?
The left one. The 2026 owner's manual says the left side panel must be removed before the right side panel. When installing, the right side panel goes on first.
How many people does it take to remove a Gladiator hard top?
The manual says removing the hard top requires four adults, one at each corner, or the top could be damaged.
What tool removes the Gladiator hard top?
The provided #50 (T50) Torx head driver and ratchet, for the two B-pillar screws, two interior body side fasteners and four fasteners along the back of the cab.
What is the torque for the hard top bolts?
The manual lists 155 in-lb +/- 22 in-lb (17.5 N-m +/- 2.5 N-m) for the Torx fasteners that attach the hard top to the body, and warns not to overtighten them.
Can I put a roof rack on the hard top?
The manual says the hard top is not designed to carry aftermarket roof racks. The factory Roof Luggage Rack, if equipped, is for Hard Top models only and is limited to 100 lb (45 kg) including the crossbars.
What are your service hours?
Monday to Friday 7 a.m. to 7 p.m. and Saturday 7:30 a.m. to 4 p.m. We are closed Sunday.
Bring your Gladiator to Streamwood
Visit Elgin CDJR at 1500 W. Lake St. in Streamwood.
Sources
Hard top and Freedom Panel information is from the 2026 Jeep Gladiator owner's manual (FCA US LLC), read November 17, 2026. Equipment varies by truck and model year; follow your own owner's manual. Our address, service hours and the models we service are from our own website, checked the same day.
- 2026 Jeep Gladiator Owner's Manual: Hard Top, Freedom Panels, Sunrider For Hard Top and Roof Luggage Rack (pp. 82-88), FCA US LLC via vehicleinfo.mopar.com, read November 17, 2026
- Jeep service center page: Jeep models serviced, service hours, address, Elgin CDJR, read November 17, 2026