Jeep Gladiator · Elgin CDJR · Streamwood, IL
Jeep Gladiator Jack Points and Tire Change
Where the 2026 Jeep Gladiator owner's manual says to place the jack, where the jack, tools and spare are stored, and its step-by-step tire change, including the lug nut torque.

The short answer
The 2026 Jeep Gladiator owner's manual says to operate the jack from the front or rear of the truck and place it under the axle tube, at the front and rear jacking locations it shows. Do not raise the truck until the jack is fully engaged, and do not jack on any other location. The jack and tools are stored under the right rear seat, and the spare is under the rear of the truck on a winch and cable, so remove the spare before jacking. Lug nut torque is 130 ft-lb (176 N·m).
Where to jack up a Gladiator
| Location | What the manual says |
|---|---|
| Front | Operate the jack from the front of the vehicle and place it under the front axle tube, as shown in the manual. |
| Rear | Operate the jack from the rear of the vehicle and place it under the rear axle tube, as shown in the manual. |
| Anywhere else | Do not attempt to raise the vehicle by jacking on locations other than those indicated. The placement for the front and rear jacking locations is critical. |
| Before lifting | Do not raise the vehicle until you are sure the jack is fully engaged, and make sure the jack will not damage surrounding truck parts; adjust its position as required. |
The manual adds that the jack is only for lifting this vehicle during a tire change, and that you should never get under a vehicle on a jack. If you need to get under it, take it to a service center where it can be raised on a lift.
From the 2026 Jeep Gladiator Owner's Manual, Jacking Instructions (pp. 219-220), read November 17, 2026.
Before you jack
- Park on a firm, level surface, away from ice, slippery areas and moving traffic.
- Turn on the Hazard Warning Flashers.
- Apply the parking brake.
- Shift an automatic transmission into PARK, or a manual transmission into REVERSE.
- Cycle the ignition to OFF.
- Block both the front and rear of the wheel diagonally opposite the one being raised. For example, if the driver's front wheel is being changed, block the passenger's rear wheel.
Passengers should not stay in the vehicle while it is jacked up, and the engine should never be started or run with the vehicle on a jack.
From the 2026 Jeep Gladiator Owner's Manual, Preparations For Jacking; Jacking Instructions (pp. 216-217, 219), read November 17, 2026.
Finding the jack and the spare
| Item | Where it is and how to get it |
|---|---|
| Jack and tools | Under the right rear seat. Fold up the seat, turn the wing bolt counterclockwise and remove it, then slide the assembly out. Release the tool bag straps from the jack and assemble the tools. |
| Spare tire | Under the rear of the truck on a winch and cable. Remove the spare before jacking up the truck. |
| Lowering the spare | Attach the lug wrench to the extension tubes with the curved angle facing away from the truck, insert them through the access hole between the lower tailgate and the top of the fascia/bumper into the winch tube, and turn counterclockwise until the tire is on the ground with enough slack. Pull it out, tilt the retainer and pull it through the wheel center. |
| Winch caution | The winch is designed for use with the jack wrench extension tool only. An air wrench or power tool may damage it. |
From the 2026 Jeep Gladiator Owner's Manual, Jack Location; Spare Tire Location And Removal (pp. 217-219), read November 17, 2026.
Changing the tire, step by step
- Remove the spare tire, jack and tools from their stored locations.
- With the wheel still on the ground, loosen (do not remove) the wheel nuts one turn counterclockwise with the lug wrench.
- Assemble the jack and jacking tools: connect the jack handle driver to the extension, then to the lug wrench.
- Place the jack under the front or rear axle tube at the location shown in the manual.
- Turn the jack screw clockwise to raise the truck only until the tire just clears the ground and there is room to install the spare. Minimum lift gives maximum stability.
- Remove the lug nuts and wheel, mount the spare on the axle, and install the lug nuts with the cone-shaped end toward the wheel. Tighten them lightly.
- Lower the truck by turning the jack screw counterclockwise, and remove the jack. Do not fully tighten the nuts until the truck is down.
- Finish tightening in a star pattern until each has been tightened twice. If in doubt, have them checked with a torque wrench by a dealer or service station.
- After 25 miles (40 km), check the lug nut torque with a torque wrench.
- Remove the jack assembly and wheel blocks, and secure the jack and tools in their proper locations.
| Lug nut torque | Lug nut size | Socket size |
|---|---|---|
| 130 ft-lb (176 N·m) | M14 x 1.50 mm | 22 mm |
The manual says to use a properly calibrated torque wrench with a six-sided (hex) deep wall socket, only use dealer-recommended lug nuts, clean off dirt or oil before tightening, and inspect the wheel mounting surface for corrosion or loose particles. For tire sizes, see our Gladiator tire size guide.
From the 2026 Jeep Gladiator Owner's Manual, Jacking Instructions; Torque Specifications (pp. 220-221, 285), read November 17, 2026.
Stowing the flat and the jack
- Slide the retainer through the wheel center, then turn the lug wrench clockwise until the wheel is drawn up against the underside of the truck. Keep turning until the winch slips or clicks three or four times; it cannot be overtightened. Push on the tire several times to check it.
- Tighten the jack down, strap it into the tool bag, place it under the rear seat and secure the wing bolt clockwise.
- Have the flat repaired or replaced immediately. A loose tire or jack thrown forward in a collision or hard stop could endanger occupants.
From the 2026 Jeep Gladiator Owner's Manual, To Stow The Flat Or Spare; Reinstalling The Jack And Tools (pp. 221-222), read November 17, 2026.
Jeep Gladiator tire and service help at Elgin CDJR
Our Mopar service department works on the Jeep Gladiator, wherever it was bought. Visit our Jeep tire service or Jeep service center pages, schedule service or see our service specials.
Our service department is open Monday to Friday 7 a.m. to 7 p.m. and Saturday 7:30 a.m. to 4 p.m., and is closed Sunday. Elgin CDJR is at 1500 W. Lake St. in Streamwood. Get directions.
Jeep Gladiator jack points FAQ
Where do you put the jack on a Jeep Gladiator?
The 2026 owner's manual says to place the jack under the axle tube, operating it from the front or rear of the truck at the front and rear jacking locations it shows. Do not jack on other locations.
Where is the jack on a Jeep Gladiator?
The manual says the jack and tools are stored under the right rear seat, held by a wing bolt.
Where is the Gladiator spare tire?
Under the rear of the truck, held by a winch and cable. The manual says to remove the spare before jacking up the truck.
What is the lug nut torque on a Gladiator?
The manual lists 130 ft-lb (176 N-m) for M14 x 1.50 mm lug nuts with a 22 mm socket, and says to check the torque again after 25 miles (40 km).
How high should I jack the truck?
Only until the tire just clears the ground and there is room to install the spare. The manual says raising it higher than necessary can make the truck less stable.
Can I use an impact gun on the spare tire winch?
No. The manual says the winch is designed for use with the jack wrench extension tool only, and an air wrench or power tool may damage it.
What are your service hours?
Monday to Friday 7 a.m. to 7 p.m. and Saturday 7:30 a.m. to 4 p.m. We are closed Sunday.
Bring your Gladiator to Streamwood
Visit Elgin CDJR at 1500 W. Lake St. in Streamwood.
Sources
Jacking and tire change information is from the 2026 Jeep Gladiator owner's manual (FCA US LLC), read November 17, 2026. Equipment varies by truck and model year; follow your own owner's manual. Our address, service hours and the models we service are from our own website, checked the same day.
- 2026 Jeep Gladiator Owner's Manual: Jacking The Vehicle And Wheel Changing (pp. 216-222) and Torque Specifications (p. 285), FCA US LLC via vehicleinfo.mopar.com, read November 17, 2026
- Jeep service center page: Jeep models serviced, service hours, address, Elgin CDJR, read November 17, 2026