Jeep Cherokee · Elgin CDJR · Streamwood, IL
Jeep Cherokee Lug Nut Torque Guide
What is the lug nut torque for a Jeep Cherokee? Here is what the 2026 Jeep Cherokee owner's manual says about the wheel bolt torque, bolt and socket size, the tightening pattern, and the steps for tightening the wheel bolts after a tire change.
130 ft-lbWheel bolt torque
176 N-mMetric equivalent
M14 x 1.50Bolt size
22 mmSocket size
The short answer
The 2026 Jeep Cherokee owner's manual lists a lug nut/bolt torque of 130 ft-lb (176 N-m), with an M14 x 1.50 lug nut/bolt size and a 22 mm socket. Tighten the lug nuts/bolts in a star pattern until each has been tightened twice, and after 25 miles (40 km), check the torque to be sure that all of them are properly tightened.
Jeep Cherokee lug nut torque specification
The manual's Torque Specifications table lists:
| Item | Specification, per the 2026 manual |
|---|---|
| Lug nut/bolt torque | 130 ft-lb (176 N-m) |
| Lug nut/bolt size | M14 x 1.50 |
| Lug nut/bolt socket size | 22 mm |
The manual says proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle. Use only authorized dealer recommended lug nuts/bolts, and clean or remove any dirt or oil before tightening.
From the 2026 Jeep Cherokee owner's manual (Wheel And Tires, Torque Specifications), read November 9, 2026.
How the manual says to tighten the wheel bolts
Any time a wheel has been removed and reinstalled on the vehicle, the manual says the lug nuts/bolts should be torqued using a properly calibrated torque wrench with a six-sided (hex) deep wall socket. Its steps are:
- Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.
- Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.
- Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it half way).
- After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly tightened.
From the 2026 Jeep Cherokee owner's manual (Wheel And Tires, Torque Specifications), read November 9, 2026. If in doubt about the correct tightness, the manual says to have them checked with a torque wrench by an authorized dealer or service station.
Tightening the wheel bolts after a tire change
In its jacking and tire changing steps, the manual says to use the wheel bolt wrench to loosen, but not remove, the wheel bolts on the wheel with the flat tire before raising the vehicle, turning them counterclockwise one turn while the wheel is still on the ground.
After mounting the spare, install and lightly tighten the wheel bolts, then lower the vehicle. Finish tightening the wheel bolts by pushing down on the wrench at the end of the handle for increased leverage, in a star pattern until each wheel bolt has been tightened twice. After 25 miles (40 km), check the wheel bolt torque with a torque wrench to ensure that all wheel bolts are properly seated against the wheel.
From the 2026 Jeep Cherokee owner's manual (Jacking Instructions), read November 9, 2026. The manual warns: to avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered.
Checking wheel bolt torque during routine checks
The manual's periodic safety checks for tires say to examine tires for excessive tread wear and uneven wear patterns, inspect the tread and sidewalls for cuts, cracks and bulges, check the lug nut/bolt torque for tightness, and check the tires (including spare) for proper cold inflation pressure.
From the 2026 Jeep Cherokee owner's manual (Periodic Safety Checks You Should Make Outside The Vehicle, Tires), read November 9, 2026.
Jeep Cherokee service at Elgin CDJR
If you would like your Cherokee's wheel bolts checked with a torque wrench after a tire change or rotation, our Jeep service center can help. Our service department is open Monday to Friday 7 a.m. to 7 p.m. and Saturday 7:30 a.m. to 4 p.m., and is closed Sunday. Elgin CDJR is at 1500 W. Lake St. in Streamwood. Get directions.
Jeep Cherokee Lug Nut Torque FAQ
What is the lug nut torque for a Jeep Cherokee?
The 2026 manual lists 130 ft-lb (176 N-m) for the lug nuts/bolts.
What size are the Cherokee lug bolts?
The manual lists an M14 x 1.50 lug nut/bolt size and a 22 mm socket size.
What pattern should I tighten them in?
A star pattern, until each nut/bolt has been tightened twice, per the manual.
Do I need to recheck the torque?
Yes. After 25 miles (40 km), the manual says to check the lug nut/bolt torque to be sure all of them are properly tightened.
Can I tighten them fully while the vehicle is on the jack?
No. The manual warns not to tighten the wheel nuts fully until the vehicle has been lowered, to avoid the risk of forcing the vehicle off the jack.
What are your service hours?
Monday to Friday 7 a.m. to 7 p.m. and Saturday 7:30 a.m. to 4 p.m. We are closed Sunday.
Bring your Jeep Cherokee to Streamwood
Visit Elgin CDJR at 1500 W. Lake St. in Streamwood.
Sources
The guidance on this page is from the 2026 Jeep Cherokee owner's manual on Mopar (PDF dated March 30, 2026), read November 9, 2026. Our address and service hours are from our own website, checked the same day.