Jeep Gladiator · Elgin CDJR · Streamwood, IL
Jeep Gladiator Door Removal Guide
How to take the front and rear doors off your Gladiator for off-road use, put them back on and reconnect the wiring, and fit the optional Door Off Mirrors, following the 2026 Jeep Gladiator owner's manual.

The short answer
The 2026 Jeep Gladiator owner's manual says door removal is for off-road operation only. For each front door: lower the window and turn the truck off, fold the mirror, remove the wiring access cover under the instrument panel, unlock and open the wiring harness and unplug the connector, remove the check arm pin, free the check arm and put the pin back in its bracket, then lift the door off its hinge pins with a second person. The rear doors follow similar steps, with the wiring under a cover at the bottom of the B-pillar. Store the doors outside the truck, never inside it.
Before you start
- Have a clean, secure storage area ready for the doors. Careless handling and storage can damage the seals and let water leak into the cab.
- Do not drive on public roads with the doors removed. The manual says the procedure is for off-road operation only, and everyone must wear seat belts off-road with the doors off.
- Do not store detached doors inside the truck. They may cause injury in an accident.
- The outside mirrors are mounted on the doors, and federal law requires outside mirrors for on-road use. The manual says to see an authorized dealer for a replacement cowl-mounted outside mirror if you choose to remove the doors.
- Doors are heavy. Two people are required to remove and install each front door.
- With the front doors removed, Blind Spot Monitoring, the power mirrors and the power door locks are unavailable.
From the 2026 Jeep Gladiator Owner's Manual, Front Door Removal (pp. 23-24), read November 17, 2026.
Taking the front doors off
- Lower the window to prevent damage and to use the door frame for support, then turn the vehicle off.
- Fold the outside mirror to the fully closed position.
- Remove the plastic wiring access cover under the instrument panel by sliding it along the door frame toward the seats until the tabs detach. Do not force it open, or the cover will break.
- Pull up on the red locking tab to unlock the wiring harness.
- Push and hold the black security tab under the harness and lift the harness lever to the open position.
- Pull straight down on the wiring connector to unplug it, and store it in the lower door basket.
- With the door fully open, remove the check arm pin: push down with your thumb to disconnect the pin clip, flip the clip upward, then pull up on it with a twisting motion until it comes out of the bracket.
- Keeping a hand on the door so it does not swing fully open, gently pull the door until the check arm is out of the bracket. Put the check arm pin back into the bracket and push the center of the clip until you feel and hear two clicks.
- With the door open, lift it with the help of another person to clear the hinge pins, and remove the door.
From the 2026 Jeep Gladiator Owner's Manual, Front Door Removal (pp. 24-25), read November 17, 2026.
Putting the front doors back on
- Remove the check arm pin from the bracket.
- With another person, using the lifting points and with the door at 90 degrees, line up the longer upper and lower hinge pins on the door and lower them onto the body hinges until fully seated. The upper hinge pin is longer, which helps guide the door into place.
- Align the check arm pin hole with the hole in the check bracket on the body, place the pin in the bracket and check arm, and flip down the pin clip. Push the center of the clip until you feel or hear two clicks, and make sure the pin is fully retained.
From the 2026 Jeep Gladiator Owner's Manual, To Install The Front Doors (pp. 25-26), read November 17, 2026.
Reconnecting the door wiring
Make sure there is plenty of slack in the wiring connector; close the door slightly for more slack if needed.
- With light finger pressure, seat the connector straight into the harness until the harness lever starts to lower.
- Keep lowering the harness lever to the fully closed position.
- Push the red locking tab down to lock it in place.
- Attach the door's cloth strap to the metal hook just inside the vehicle.
- Replace the wiring access covers.
The manual warns that failing to reconnect the wiring connector correctly will cause damage that is not covered by the New Vehicle Warranty. Keep arms, hands and fingers clear of the check arm area during removal and installation.
From the 2026 Jeep Gladiator Owner's Manual, Replacing The Wiring Connector Into The Wiring Harness (p. 26), read November 17, 2026.
Taking the rear doors off
- Roll down the window to prevent damage.
- Slide the front seat or seats fully forward.
- Pry open and remove the plastic wiring access door at the bottom of the B-pillar.
- Unplug the wiring connector. Squeeze the tab on the base of the harness to unlock the connector tab.
- With the door fully open, remove the check arm pin the same way as on the front door.
- Keeping a hand on the door, gently pull it until the check arm is out of the bracket, then put the pin back in the bracket and push the clip until you feel and hear two clicks.
- With the door at 45 degrees or more from the shut position, lift it with the help of another person to clear the hinge pins, and remove it.
To reinstall the rear doors, do these steps in reverse order. The upper hinge has the longer pin to help guide the door into place.
From the 2026 Jeep Gladiator Owner's Manual, Rear Door Removal (pp. 26-28), read November 17, 2026.
Door Off Mirror kit (if equipped)
If your Gladiator has the Door Off Mirror Kit, outside mirrors can be installed on the upper body door hinges after the front doors are removed.
- Remove both front doors.
- Remove the cowl bolt closest to the door opening with a #40 Torx head driver, and store it in a safe place.
- Push the mirror bracket forward onto the A-pillar, lining up the bottom of the bracket with the upper door hinge and the hole from the removed cowl bolt.
- Place the bracket bushing behind the mirror bracket, over the cowl bolt hole, and insert the bracket bolt through the mirror bracket and bushing.
- Insert the hinge shoulder bolt up through the bottom of the upper door hinge into the mirror bracket, then rotate the bracket knob toward the rear to secure the bracket to the A-pillar.
- Tighten the bracket bolt and hinge shoulder bolt with a #40 Torx head driver.
- Lower the mirror assembly onto the mirror bracket.
- Insert the three mirror screws and tighten them into the bracket with a #30 Torx head driver.
- Repeat on the other side.
| Fastener | Recommended torque |
|---|---|
| Mirror bracket bolt | 6 ft-lb (8 N·m) |
| Hinge shoulder bolt | 7.5 ft-lb (10 N·m) |
| Mirror screws (3) | 4 ft-lb (5.5 N·m) |
If the kit is installed with the optional lamp bracket, the bracket bushing is not needed; use the spacer from the lamp bracket. Own a Wrangler too? See how to take the doors off a Wrangler.
From the 2026 Jeep Gladiator Owner's Manual, Door Off Mirror Kit (pp. 28-29), read November 17, 2026.
Jeep Gladiator service and parts at Elgin CDJR
Our Mopar service department works on the Jeep Gladiator, wherever it was bought. Visit our Jeep service center or parts center, schedule service or see our service specials.
Our service department is open Monday to Friday 7 a.m. to 7 p.m. and Saturday 7:30 a.m. to 4 p.m., and is closed Sunday. Elgin CDJR is at 1500 W. Lake St. in Streamwood. Get directions.
Jeep Gladiator door removal FAQ
Can I drive a Jeep Gladiator with the doors off?
The 2026 owner's manual says not to drive on public roads with the doors removed, because you lose the protection they provide. It says the door removal procedure is for off-road operation only, with everyone wearing seat belts.
How many people does it take to remove a Gladiator door?
The manual says doors are heavy and two people are required to remove and install each front door. It also says to lift the rear doors with the help of another person.
What stops working when the front doors are off?
The manual says Blind Spot Monitoring, the power mirrors and the power door locks are unavailable when the front doors are removed.
Where should I keep the doors?
Outside the truck, in a clean, secure storage area. The manual warns not to store detached doors inside the vehicle.
What tools do the Door Off Mirrors need?
A #40 Torx head driver for the cowl bolt, bracket bolt and hinge shoulder bolt, and a #30 Torx head driver for the three mirror screws.
What are your service hours?
Monday to Friday 7 a.m. to 7 p.m. and Saturday 7:30 a.m. to 4 p.m. We are closed Sunday.
Bring your Gladiator to Streamwood
Visit Elgin CDJR at 1500 W. Lake St. in Streamwood.
Sources
Door removal and installation information is from the 2026 Jeep Gladiator owner's manual (FCA US LLC), read November 17, 2026. Equipment varies by truck and model year; follow your own owner's manual. Our address, service hours and the models we service are from our own website, checked the same day.
- 2026 Jeep Gladiator Owner's Manual: Front Door Removal, Rear Door Removal and Door Off Mirror Kit (pp. 23-29), FCA US LLC via vehicleinfo.mopar.com, read November 17, 2026
- Jeep service center page: Jeep models serviced, service hours, address, Elgin CDJR, read November 17, 2026